Whilst the sales literature is all about the Dell Wyse 5060 my 5060 is physically identified as a N07D. There is no mention of '5060' on either side of the label.
It soon became clear to me that the 5060 is just an evolution of the Wyse D Class thin clients. The case size is identical, and looking at the specifications section in the User Manual I find the entry "Chassis Leveraged: Dell Wyse 5020 (Oberon)". (A strange comment. Something you'd expect in an internal design document rather than in a public document).
When I removed the side panel I could see that the motherboard was just a reworked version of the one in the 5020 (Dx0Q). Basically the same board with a few small alterations. One obvious change was that the WLAN socket had switched from mPCIe to M.2.
The basic specs are:
Processor Type
SpeedQuad core AMD GX-424
2.4GHzMemory Flash
RAM8GB
4GB (max 16GB)Video Chip
Max resolutionAMD Radeon R5E Graphics
Dual Display
2560 x 1600 @60Hz or
3840 x 2160 @30HzPorts Video
Network
USB
Serial
Parallel
PS/22 x Display Port
10/100/1000
4 x USB2.0
2 x USB3.1
0
0
0Power Plug
Off
Idle
RunningCoax 5.5mm/2.5mm
1W
8W
17WDimensions H x W x D (mm) 170 x 40 x 185
Operating systems:
Wyse ThinOS and Wyse ThinOS with PCoIP
Wyse ThinLinux
Windows Embedded Standard 7 Pro (64bit) (with WIE10 license)
Windows 10 IoT Enterprise (64bit)
No power supply came with this so I used a 19V 3.42A Delta Electronics PSU. As always note the 19V rating. If, like me, you have a number of PSUs and thin clients floating around you need to mark this PSU clearly in some way. I'm sure that those which run from 12V - which is most of them - would not take too kindly to 19V. The coax plug is 5.5mm/2.5mm.
The figures given in the table above are from my observations from when the system starts up with my standard USB keyboard and mouse plugged in.
Adam provided me with some additional details:
This is fairly straightforward. You need to remove the foot (if fitted) and then the three screws on the back panel. The plastic side cover then slides back a short way can be lifted off. This reveals a metal shield that is dealt with in a similar fashion. This time there are screws in each corner to be removed and a final one in the centre of the edge by the front panel. Once again this panel is slid a short distance towards the rear before it can be lifted clear. (There are three metal lugs each side that locate in small slots in the metal chassis that lock it in place). The speaker is fixed to this panel and will need to be disconnected from the board near to the SODIMM.
The GX-424CC is an AMD 64-bit Quad core CPU clocked at 2.4GHz.
vendor_id : AuthenticAMD cpu family : 22 model : 48 model name : AMD GX-424CC SOC with Radeon(TM) R5E Graphics stepping : 1 flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good acc_power nonstop_tsc cpuid extd_apicid aperfmperf pni pclmulqdq monitor ssse3 cx16 sse4_1 sse4_2 movbe popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt topoext perfctr_nb bpext ptsc perfctr_llc hw_pstate ssbd vmmcall bmi1 xsaveopt arat npt lbrv svm_lock nrip_save tsc_scale flushbyasid decodeassists pausefilter pfthreshold overflow_recov
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 1566 00:01.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Mullins [Radeon R4/R5 Graphics] (rev 01) 00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Kabini HDMI/DP Audio 00:02.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 156b 00:02.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1 00:02.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1 00:02.3 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1 00:02.4 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1 00:02.5 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1 00:08.0 Encryption controller: Advanced Micro Devices, Inc. [AMD] Device 1537 00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 11) 00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 39) 00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 39) 00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 39) 00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 42) 00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 02) 00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11) 00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 1580 00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 1581 00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 1582 00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 1583 00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 1584 00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 1585 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 15)
Flash: The flash is a small horizontal SATA DOM. The board is also tracked for a separate SATA data connector that is not fitted to my example.
I tried out an 8GB PC3L SK Hynix part (HMT41GS6BFR8A-PB NO AA). This worked.
As with the Dx0Q the lower RAM socket is a little awkward to use. I haven't tried it with this unit but I assume it's just a matter of removing the front panel as described in the Dx0Q entry.
WLAN+BT Combo Module: Intel 7265 M.22230 (PCIe/USB interface)
As with the Dx0D I haven't taken the motherboard out of the housing, but I did notice whilst peering in through the ventilation slots, a push switch mounted on the rear of the board. marked 'BIOS Recovery'.